|
Introduce to you new tablet press "Tabletpress 6000S" :
there Is a new updating of it
Desktop the press - to read more in detail " Tabletpress 6000
NEW "
Photos spare parts to Tabletpress 6000S
You can see the increased photos! Press a photo for
Viewing in a separate window.
The Bed tablet press:
   
Photos a bed tablet press. Gross weight of a bed - 40 kg.
Lab tablet press can be dismantled easily. It creates
Convenience in transportation. A bed tselno-cast from pig-iron. Application
High-quality stamps of pig-iron allows to refuse use
Brass or copper cartridges.
In the case press the switch is located. Closely study yours press,
Before to start it in job check up correctness electric
schemes.
The Debugging wheel and protection of a gear:
 
In the complete set of delivery there is a wheel for manual debugging press. In process
Debugging jobs rotate a wheel, for the available handle, clockwise.
The direction of rotation press is specified on the tablet which is on
A protective casing of a gear. Operation press without protective is forbidden
A casing. An adjusting wheel at the moment of start press in manufacture (
Attention!!! Only after fixing adjustments press!!!) it is possible to dismantle
(To remove)
Fastening of punches tabletpress:
 
Pressing is carried out by two punches (top and bottom) - on
Photos sites of fastening of the top and bottom punch in gathering. Bottom
The holder fixes a punch in the top, two adjusting gears fix
Position of the bottom punch in a matrix. It allows to adjust volume
Loadings a matrix by a powder. One of shesteren fixes position bottom
A punch in the top point, at pushing out of a ready tablet from a matrix.
Between zubjami shesteren the plate which is established fixes adjustment
Also does not give to weaken this site during all operating time press. Between
Two gears fix a plug with an axis of draft. For this draft the bottom punch
Also rises upwards.
Держатель the top punch in gathering has the case in which it is located
The clown. The punch is fixed in a body of a pusher, for dismantle it is necessary
To weaken fixing nut. In the basis of a pusher there is a mechanism
Regulations of force of compression (and heights of a ready tablet). I follow the instruction
The user study process of adjustment of it knot.
The Pusher and Draft with a plug:
 
One more photo of a pusher with the top punch in gathering. On another
Photos - draft with a plug which is fixed by two nuts .
big gear and the Pulley with a small gear:
 
The effort from the engine, through a belt drive, is passed to the big pulley with
A small gear. Further from a small gear pressure is passed on big
A gear. On a photo the big gear "red". The pulley has a groove under
A belt structure - and. The small gear is established on an axis of the basis of a pulley. A pulley with
The gear in gathering establishes in a landing place in a bed press. With
A lateral face in a pulley there are apertures in diameter of 13 mm which serve
For provorachivanija a shaft press at jamming. Complete with presses goes
The lever which if necessary establish in the specified apertures and
Rotate a shaft press.
Kopiry:
 
Kopir a pusher, it is fixed on the basic to a shaft and serves for
Periodic pushing out of a ready tablet on a surface of a desktop in
Which the matrix is fixed. The second kopir actuates rotary
A paw of submission of a powder in a matrix. If closely to study a photo it is possible
To notice three repeating elements. Feature of the given model press
Triple arrival of a paw submitting a powder on a matrix, that is
Is guaranteed adjusts quality of filling of a powder. During job
The roller sliding in a figured groove makes three movements before top
The punch will plunge into a matrix.
The Basic shaft and a table of fastening of a matrix:
 
On the basic shaft many details press put on, is structurally stipulated
Exception of wrong assembly press. Study a photo of a table in which
Replaceable matrixes are fixed. From the face party to be the clamp of matrixes,
At editing place a new matrix in an aperture and record tight.
Bunker and a rotary paw:
 
Portion submission of a powder in a matrix is carried out from the bunker rotary
A paw. In a photo - the bunker is executed from corrosion-proof began. The bunker
It is suspended to a bed on a special arm, and a working part
Is located in a rotary paw. Volume of the bunker press - 2 litres. In a photo
- a rotary paw in gathering. From the bottom party the screw is twisted in a paw with
A spring, resting in a window in a table with a matrix the spring provides dense
prileganie planes of a paw to a surface of a table. Force of a clip can
regulate.
The Holder engine:
To a bed the holder of the engine is fixed. The design of the holder allows
To carry out a tension of a belt of a drive. Closely study a design
The holder if you will find necessary to increase capacity press, to you
It is required to establish more powerful engine. Use the holder for
Installations of the new engine. Drill apertures for fastening observing
A parity of grooves of pulleys. Tightening belts it is made by the screw
Attached to a bed press and taking place in a groove of the holder.
To read the full version about technology
Pharmaceutical manufacture of medicines in section " TECHNOLOGIES "
We offer you
our link base:
OUR WEB SITES
and
USEFUL LINKS.
Free small video
clips about our equipment :
|
